Configuration 1
A fluoroplastic sump pump for corrosive liquid transfer from tanks and pits. The supplied technical sheets are from the HYF manual. Confirm immersed length, liquid level, fluoroplastic grade and shaft-sealing arrangement.
Fluoroplastic Sump Pump
Fluoroplastic Sump Pump
Corrosive-liquid transfer from tanks and pits.
A fluoroplastic sump pump for corrosive liquid transfer from tanks and pits.
Related resources: Chemical and petrochemical pump selection
- Installation
- Vertical tank / sump installation
- Wet end
- Fluoroplastic; confirm exact grade
- Sealing
- Confirm immersed shaft and sealing design
- Drive
- Motor above the liquid
models
Fluoroplastic Sump Pump models & specifications
Check model references against the original performance table, speed, materials and operating conditions.
| Model reference | Catalogue scope | Specifications | Enquiry |
|---|---|---|---|
| 25HYF-41 | Original catalogue reference | Source PDF ↗ | |
| 25HYF-25 | Original catalogue reference | Source PDF ↗ | |
| 25HYF-16 | Original catalogue reference | Source PDF ↗ | |
| 40HYF-40 | Original catalogue reference | Source PDF ↗ | |
| 40HYF-26 | Original catalogue reference | Source PDF ↗ | |
| 40HYF-16 | Original catalogue reference | Source PDF ↗ | |
| 50HYF-25 | Original catalogue reference | Source PDF ↗ | |
| 50HYF-16 | Original catalogue reference | Source PDF ↗ | |
| 65HYF-40 | Original catalogue reference | Source PDF ↗ | |
| 65HYF-25 | Original catalogue reference | Source PDF ↗ | |
| 65HYF-16 | Original catalogue reference | Source PDF ↗ | |
| 100HYF-57 | Original catalogue reference | Source PDF ↗ | |
| 100HYF-37 | Original catalogue reference | Source PDF ↗ | |
| 100HYF-23 | Original catalogue reference | Source PDF ↗ |
Original technical pages
The supplied technical sheets are from the HYF manual. Confirm immersed length, liquid level, fluoroplastic grade and shaft-sealing arrangement.
configurations
Available configurations
Configuration 2
A fluoroplastic sump-pump series for corrosive-liquid duties in chemical, pharmaceutical and environmental processes. The shared fact record identifies FYS, but the available parameter sheet is labelled HYF. It is not an FYS rating table. Request an FYS-specific curve and arrangement.
overview
Fluoroplastic Sump Pump construction and operation
Fluoroplastic sump-pump arrangement
The hydraulic end is immersed in the sump while the drive remains above the liquid. Tank depth, operating levels, mounting plate and column arrangement define the installation.
A fluoroplastic sump pump for corrosive liquid transfer from tanks and pits.
- Pump body operates below the tank liquid level
- Fluoroplastic wetted materials require chemical-compatibility review
- Immersion length, liquid-level changes and shaft sealing define the installation
AI-generated family illustrations. The selected configuration follows the agreed model and drawing.
construction
Components, materials and seals
Immersed pump body
The hydraulic end operates below liquid level. Define the lowest and highest operating levels.
Fluoroplastic materials
Confirm the actual FEP, PVDF or other specified grade against the complete liquid composition.
Shaft & column
Immersion length and tank dimensions determine the shaft and support arrangement.
Mounting & discharge
Match the installation plate, discharge connection and lifting clearance to the tank layout.
AI-generated family illustrations. The selected configuration follows the agreed model and drawing.
duty requirements
Materials, sealing & duty requirements
Review medium name and composition, required flow, total head, operating temperature, suction conditions, installation arrangement, power supply and drive method, materials, standards and inspection requirements, required supply scope, full chemical composition and concentration, density and viscosity, flammability, toxicity, crystallisation and volatility, design pressure and temperature, seal and flushing requirements, applicable process standard together with the liquid composition, temperature and installation. The values on a catalogue page are not a substitute for checking the selected model curve and approved arrangement.
| Wetted components | Fluoroplastic; confirm exact grade |
|---|---|
| Sealing | Confirm immersed shaft and sealing design |
| Liquid / design limits | Confirm liquid composition, temperature, particles and operating conditions |
| medium name and composition | Include this information in the duty review and model selection |
| required flow | Include this information in the duty review and model selection |
| total head | Include this information in the duty review and model selection |
| operating temperature | Include this information in the duty review and model selection |
| suction conditions | Include this information in the duty review and model selection |
| installation arrangement | Include this information in the duty review and model selection |
| power supply and drive method | Include this information in the duty review and model selection |
| materials, standards and inspection requirements | Include this information in the duty review and model selection |
| required supply scope | Include this information in the duty review and model selection |
| full chemical composition and concentration | Include this information in the duty review and model selection |
| density and viscosity | Include this information in the duty review and model selection |
| flammability, toxicity, crystallisation and volatility | Include this information in the duty review and model selection |
| design pressure and temperature | Include this information in the duty review and model selection |
| seal and flushing requirements | Include this information in the duty review and model selection |
| applicable process standard | Include this information in the duty review and model selection |
AI-generated family illustrations. The selected configuration follows the agreed model and drawing.
installation
Installation & drive arrangement
Mounting & immersion
Provide tank dimensions, mounting-plate interfaces and operating liquid levels to determine immersion length.
Shaft & motor
Review column / shaft support, driver, discharge piping and maintenance clearance. Confirm bearing-flush requirements for the configuration.
Before installation
- Foundation / mounting and pipe supports
- Liquid supply and discharge connections
- Electrical supply and maintenance access
AI-generated family illustrations. The selected configuration follows the agreed model and drawing.
applications
Typical applications
chemical processing
For chemical processing, provide the complete composition, concentration, temperature and seal-utility requirements. Check the proposed arrangement against vertical tank / sump installation and fluoroplastic; confirm exact grade, then verify the operating point on the selected model curve.
pharmaceutical processing
For pharmaceutical processing, check the applicable product curve, liquid properties, required operating point and installation geometry. Check the proposed arrangement against vertical tank / sump installation and fluoroplastic; confirm exact grade, then verify the operating point on the selected model curve.
metallurgy
For metallurgy, check the applicable product curve, liquid properties, required operating point and installation geometry. Check the proposed arrangement against vertical tank / sump installation and fluoroplastic; confirm exact grade, then verify the operating point on the selected model curve.
environmental services
For environmental services, check the applicable product curve, liquid properties, required operating point and installation geometry. Check the proposed arrangement against vertical tank / sump installation and fluoroplastic; confirm exact grade, then verify the operating point on the selected model curve.
supply scope
Choose the supply scope for this pump
Define the pump configuration, installation interfaces, controls and documents in the quotation.
Pump assembly
Hydraulic end, materials, sealing and interfaces for your driver or installation.
Electric pump set
Pump and matched motor, coupling / transmission, base and guarding as applicable.
Installation & controls
Agreed supports, controls, auxiliaries, spares and technical documents.
AI-generated family illustrations. The selected configuration follows the agreed model and drawing.
manufacturing
From preparation to shipment
Casting of pump components
Casting produces pump components to the construction and material requirements of the selected equipment. The applicable alloy, pattern and component geometry depend on the pump family and the agreed operating conditions.
Finish machining
Machining prepares mounting faces, bores, fits and connection interfaces for assembly. OEM parts should be reviewed against the approved drawing and revision, including the dimensions that determine interchange and installation.
Component handling & staging
Owner-supplied factory photograph showing pump castings staged in a work area. The exact parts and process route depend on the selected order.
Inspection equipment & controls
Owner-supplied factory photograph showing test-control equipment. The inspection points and acceptance records must be agreed for the selected equipment.
documents
Technical documents
Source catalogue
Original series manual and technical references. Review the applicable model, version and units.
Open original PDF View family brochure ↗Model-specific documents
Request the selected model curve, arrangement drawing, materials, installation instructions and agreed inspection records.
Request technical documentsquestions
Fluoroplastic Sump Pump FAQs
How do I select a model?
medium name and composition; required flow; total head; operating temperature; suction conditions; installation arrangement; power supply and drive method; materials, standards and inspection requirements; required supply scope; full chemical composition and concentration; density and viscosity; flammability, toxicity, crystallisation and volatility; design pressure and temperature; seal and flushing requirements; applicable process standard. Review the complete duty on the applicable model curve.
Which materials and sealing can be supplied?
Fluoroplastic; confirm exact grade. Confirm immersed shaft and sealing design. Confirm compatibility with the complete liquid composition and temperature.
Are catalogue model references guaranteed duty points?
Catalogue ranges summarize printed records and may combine different conditions. Check each model against its source curve and required speed.
What is included in the delivery?
Confirm pump, driver, controls, auxiliaries, spares, drawings, manuals and required test records in the agreed quotation.
enquiry
Tell us about your pump duty
Describe the liquid, required output and site arrangement so BBP can review the model and equipment scope.
- medium name and composition
- required flow
- total head
- operating temperature
- suction conditions
- installation arrangement
- power supply and drive method
- materials, standards and inspection requirements
- required supply scope
- full chemical composition and concentration
- density and viscosity
- flammability, toxicity, crystallisation and volatility
- design pressure and temperature
- seal and flushing requirements
- applicable process standard