SLURRY PUMP COMPONENTS
Slurry Pump Spare Parts
Identify the part. Match the assembly.
Identify slurry pump spare parts by pump model, part number, material and assembly position. Send the nameplate and component photographs or drawings so that wear parts, seals and bearing components can be checked for compatibility.
Related resources: Mining slurry and tailings transfer
- Installation
- Replacement components
- Wet end
- Metal or elastomer components matched to an identified assembly and agreed material specification.
- Drive
- Existing assembly to identify
- Selection
- Part reference & assembly drawing
Identify the component & compatibility
Impellers and liners
Existing part number, impeller diameter, mounting thread or bore and material.
Seals and bearing assemblies
Seal arrangement, shaft dimensions, bearing references and lubrication method.
Matched replacement sets
Assembly drawing, revision, mating components, quantities and required dimensional checks.
These are component-identification requirements. The catalogue illustrations explain the assembly; they do not establish interchangeability with a third-party pump.
Have a worn part to identify?
Use the enquiry checklist below to prepare part references, dimensions and material requirements.
A closer look at the components
Slurry pump parts include the impeller, volute or liners, throatbush, cover components, shaft-seal parts and bearing assembly. The correct replacement is defined by the installed assembly and drawing revision, rather than by a similar shape in a photograph.
Start with the pump nameplate, assembly drawing, existing part reference and photographs of the worn component. Add key dimensions, material identification and the slurry conditions. These details help separate a fit problem from a material or operating issue, and establish whether an individual wear part or a matched component set is needed.
- ✓Wet-end identificationMatch impeller, throatbush and liner interfaces before selecting the replacement.
- ✓Material and wear reviewInclude the current material, wear pattern and liquid conditions when discussing alternatives.
- ✓A traceable parts enquiryUse drawing revision, part reference, quantity and inspection scope to define the order.
Wear parts, seals & rotating assemblies
Impellers & liners
Match diameter, mounting interface and material to the existing assembly. Photograph both locating faces of the removed component.
Throatbush & covers
Provide drawing revision, mating dimensions and the condition of adjacent liners and covers before defining the replacement set.
Seal components
Identify the packing, expeller or mechanical-seal arrangement, shaft dimensions and any required utility connections.
Shaft & bearing assembly
Review shaft, bearing, housing, fits and lubrication as an assembly; use the installed drawing and references.
Information that makes a parts enquiry useful
| Review item | Required information |
|---|---|
| Wetted components | Metal or elastomer components matched to an identified assembly and agreed material specification. |
| Sealing / interfaces | Existing assembly drawing and seal part references |
| Solids information | Wear pattern and the slurry currently being handled |
| Liquid conditions | Complete chemistry, liquid and solids densities, operating temperature |
| Installation information | Drawing revision, dimensions, fits and required quantities |
Prepare an identified parts list
- ✓Installed pump & drawing revision
- ✓Part number & material
- ✓Dimensions & photographs
- ✓Quantity & inspection scope
AI-generated family illustrations. The selected configuration follows the agreed model and drawing.
Compatibility & replacement planning
Verify the interfaces
Review locating faces, bores or threads, joint details and material before agreeing the replacement. Use actual measurements and the applicable drawing.
Plan the replacement work
Follow the installed equipment instructions for isolation, draining, lifting and assembly. Record the condition of mating parts before replacement.
- ✓Isolate equipment
- ✓Verify drawings
- ✓Check mating surfaces
- ✓Use installation instructions
Maintenance & spare-parts planning
Application descriptions are selection contexts. Suitability depends on the selected equipment and actual process conditions.
Planned maintenance
Prepare an identified wear-parts set around the installed assembly and scheduled replacement work.
Wet-end repair
Record the condition of mating parts before deciding the complete repair scope.
Spare-parts inventory
Separate part identity, material and revision when building a stock list for several pumps.
Choose the supply scope
Select a scope below to carry it into the enquiry. The final equipment and documents are defined in the quotation.
Individual wear parts
Identified impeller, liner, throatbush or other component in an agreed material.
- ✓Part reference and quantity
- ✓Dimensions and material
- ✓Packing and identification
Matched component set
Related components reviewed together against the same assembly drawing.
- ✓Drawing and revision
- ✓Mating component interfaces
- ✓Replacement scope
Inspection & records
Agree the dimensional checks, material records and handover documents.
- ✓Inspection requirements
- ✓Material identification
- ✓Assembly references
Define what arrives with the equipment
Equipment & interfaces
Part identities, quantities, mating dimensions, materials and any assembled subunits.
Inspection & documentation
Agree drawing revision, inspection requirements, applicable acceptance criteria and the documents required with delivery.
Packing & service spares
Specify preservation, packing, identification and an initial spare-parts list appropriate to the maintenance plan.
From preparation to shipment
Components & material review
Identify component drawings and materials for the agreed pump or parts scope.
Machining & interfaces
Check the critical faces, bores, fits and connections against the applicable drawing.
Inspection planning
Agree inspection points, acceptance criteria and any requested records before supply.
Packing & handover
Confirm identification, preservation, packing and the documents required for handover.
Technical documents
Slurry family brochure
Product arrangements and original family drawings. Confirm the applicable series and model.
Assembly & parts schedule
Request the agreed drawing revision, material and inspection schedule.
Parts questions
Does a similar-looking component guarantee fit?
What should I send with the enquiry?
Are the images dimensional drawings?
What is included in the quotation?
Can the material be changed?
How do I use this enquiry form?
Identify the parts you need
A precise parts request starts with the installed assembly.
- ✓AssemblyPump identity, drawing and revision.
- ✓ComponentPart reference, dimensions and material.
- ✓SupplyQuantity, inspection and documents.